Welcome to visit Jiangsu Changshi Drying Technology Co., Ltd Official website!
0086-519-88908565
Home > News > Industry news
News

Four process design methods for rotary flash dryer

Information sources: | Release date: 2018-02-28 | Browse volume:463
Key word:旋转闪蒸干燥机工艺
The new equipment of rotary flash dryer adopts a variety of advanced devices. For example, a variety of feeding devices are used to make the feeding continuous and stable, and the feeding process does not cause bridging; the bottom of the dryer uses a special cooling device to avoid the material in the bottom high temperature zone. Sticking wall and deterioration phenomenon occur; special air pressure sealing device and bearing cooling device are used to effectively extend the service life of the transmission part; special air separation device is adopted to reduce the resistance of the equipment and effectively provide the processing air volume of the dryer; drying room It is equipped with a grading ring and a swirling plate to adjust the fineness and final moisture of the material. The stirring and pulverizing device is used to produce strong shearing, blowing and rotating effects on the material; air filter, cyclone separator, bag filter, etc. are used. Effectively remove dust and avoid environmental and material pollution. The device has strong mass transfer heat transfer, high production intensity, short drying time and short material residence time. So today, the experienced drying equipment manufacturers in Changzhou will introduce the four process design methods of rotary flash dryers!

First, the determination of the drying room
The rotary flash dryer processes the evaporation strength of some materials. The volumetric heating method is the theoretical design method of the rotary flash dryer. However, the most critical volumetric heat coefficient in this method is difficult to determine, so it lacks operability. Evaporation intensity method is an indirect method of volumetric heating method. It can be calculated as long as there is certain experimental data. It is a method commonly used in industrial design. The evaporation strength method calculates the volume of the drying chamber based on the amount of evaporated water and the evaporation strength, and calculates the effective height based on the relationship between the diameter and the height.

Second, the diameter of the drying chamber
Another method is to calculate the required air consumption by material balance and heat balance, and then determine the diameter of the dryer according to the air speed range.

Third, the height of the dryer and the graded particle size
The hot air from the hot air distributor enters the drying chamber through the annular gap in a tangential direction, and the material in the drying chamber is spirally rotated and raised under the action of the hot air blowing and the agitator. When studying the fluid motion of smaller particles under the action of the centrifugal force field, the effect of gravity is small and therefore negligible.

Fourth, the application of rotary flash dryer
The operating conditions of the partial rotary flash dryer, the upper part of the drying chamber is provided with a step ring, the main function of which is to separate the material with large or no dry particles from the qualified product, and the product in the drying chamber can effectively ensure the product granularity and moisture requirement. Replacing the grading rings of different diameters can meet the product size requirements. Cold air protection is provided at the hot air population at the bottom of the cone to prevent the material from coming into contact with high temperature air to cause overheating. The drying system is closed and operates under micro-negative pressure. The dust does not leak, protecting the production environment, and being safe and hygienic.

Related articles
Related products
  • Stainless steel containers
    Stainless steel containers
  • ZSL-III  Series Vacuum Feeder
    ZSL-III Series Vacuum Feeder
  • TJG  Series Fixed Lifting Feeder
    TJG Series Fixed Lifting Feeder
  • CG Series Forming Machine
    CG Series Forming Machine
  • ERT Series Alcohol Recovery Tower
    ERT Series Alcohol Recovery Tower
  • MF Series Pulse Bag Filter
    MF Series Pulse Bag Filter
  • SRQ Series Heat Exchanger
    SRQ Series Heat Exchanger
  • RLY Series Oil Combustion Hot Air Furnace
    RLY Series Oil Combustion Hot Air Furnace
Main: double cone rotary vacuum dryer, rake dryer, flash drying equipment, hollow blade dryer, sludge dryer, airflow dryer, centrifugal spray dryer, single cone screw vacuum dryer, vacuum crucible Dryer, etc.
Top